CURT 31432 2-tolline eesmine vastuvõtja haakeseade, valige Jeep Wrangler JK, must

Name: CURT 31432 2-tolline eesmine vastuvõtja haakeseade, valige Jeep Wrangler JK, must
Brand: CURT
SKU: 0612314314324
Price: 517.52 EUR
Availability: InStock

Brand:CURT

3.5/5

€
517.52

CURT esihaagise konks võimaldab teil kasutada oma sõiduki esiotsa mitmesugusteks pukseerimistöödeks. Neid saab kasutada vintsi, lumesaha ja mitmete pukseerimistarvikute paigaldamiseks ning neid saab kasutada isegi mõnel haagisel vedamisel. Kui ruumi on vähe, kasutatakse tavaliselt lastikanduri hoidmiseks eesmist haagisekonksu, mis vabastab sõiduki sees ruumi lisaveosele ja muudab tagahaagise vastuvõtja haagise tõmbamiseks kättesaadavaks. Paadi kaldteel saab teie paadihaagise kinnitada eesmise vastuvõtja haakeseadme külge, mis annab teile veeskamisel haagise üle parema kontrolli. Mõned muud lisaseadmed, mida saab kasutada koos eesmise veokonksuga, on CURT vintsi kinnitus, astmepadi, numbrimärgi hoidik, varurehvi kinnitus, libisemiskaitse ja veokonksud. Kõik CURTi esihaagise haakeseadmed pakuvad kasulikku vastuvõtjatoru 2 x 2 varre vastuvõtmiseks ning neid kasutatakse tavaliselt veoautodel, kaubikutel ja maasturitel. Selle esihaagise haakeseade kaalub 3500 naela. GTW ja 350 naela. TW. Sellel on ka sirgjooneline tõmbejõud 9000 naela. See on mõeldud Jeep Wrangler JK teatud aastate jaoks kohandatud haagisekonksuks (sobivuse kontrollimiseks vaadake rakenduse teavet). Sellega on kaasas kogu täielikuks installimiseks vajalik riistvara ja sellel on piiratud eluaegne garantii.

Ühikuid pole saadaval

EAN: 0612314314324

Kategooriad Autotooted, Emberkauba tarvikud, Pukseerimistooted ja vintsid, Koormakinnitused, Vastuvõtjad,

LIHTNE PAIGALDAMINE. See eesmine veokonks on konstrueeritud sõidukispetsiifilise disainiga, et see sobiks valitud Jeep Wrangler JK mudelitega. KORROSIOONI KINDEL. Suurepäraseks kaitseks rooste, mõranemise ja UV-kahjustuste eest on see esikonks kaetud kahekihilise roostekindla A-kattega, mis katab konksu seest ja väljast, ning ülimalt vastupidava musta pulbervärviga. TESTITUD EHITUS. Seda esikinnituse haakeseadet on meie Detroidi insenerikeskuses teie ohutuse tagamiseks täielikult testitud. Testime oma esihaagise konksu konstruktsioone vastavalt SAE J684 spetsifikatsioonidele. USALDUSVÄÄRSUS. Selle esihaakeseadisega on arvestatud 3500 naela. GTW ja 350 naela. keele kaal. See on hinnatud ka 9000 naela. sirgjooneline tõmbejõud pukseerimis- ja vintsirakenduste jaoks (piiratud madalaima hinnanguga pukseerimiskomponendiga). MITMEKÜLGNE VASTUVÕTJA. Selle esikinnitusega vastuvõtjakonksuga lisage oma sõiduki esiosale kasulik haakekonksu vastuvõtja. Standardne 2-tolline vastuvõtja võimaldab kinnitada lumesaha, kaubahoidiku, jalgrattahoidja, veokonksu, vintsi kinnituse või muu pukseerimistarviku.

Brand	CURT
Brand	‎CURT
Customer Reviews	4.4 4.4 out of 5 stars 133 ratings 4.4 out of 5 stars
Exterior	‎Gloss Black Powder Coat
Finish Type	Powder Coated
Is Discontinued By Manufacturer	‎No
Item model number	‎31432
Item Weight	25 Pounds
Item Weight	‎25 pounds
Manufacturer	‎Curt Manufacturing
Manufacturer Part Number	‎31432
Material	Carbon Steel
Model	‎Front Mount Hitch
OEM Part Number	‎31432
Product Dimensions	‎33 x 18 x 12 inches
Vehicle Service Type	Marine-Personal-Craft, Van, Car, Sport-Utility-Vehicles, Truck, Trailer

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: THM

Definitely 45 minutes!

One of the ads for this indicated it was a 45 minute install. NOT! I've been doing mechanical type work on automobiles and aircraft for most of my life... about 45 years now. This took me like two hours. This particular part was for my Jeep Wrangler JK. There are some hidden holes you have to use "fish spring" wire to get the bolts through the hole. It is not easy and can be very time consuming. Once installed, it is SOLID!

Scritto da: Ken Maldonado

Went into my 2015 Sahara with very minor difficulty.

The idea of having a front hitch on the Jeep is great. Allows for extra carry space with a hitch attachment for a vehicle that is highly capable but short on space. The installation process itself is pretty straightforward, but it is difficult. It took me three days but that was doing the process bit by bit once I got home from work. If I had to estimate, I would say six hours overall, so definitely a weekend project. The most difficult part was simply getting the handle nuts to align. That by itself took me maybe three hours. Try as I might I just could not get it going. But once it finally caught, it was easy to tighten down everything. I did not remove my bumper and I did not remove the brake booster pump. Luckily I have long slender fingers and was able to reach around it. Also, I did my installation by lifting the front onto ramps. Made it a lot simpler to literally get under the Jeep. That could be the reason it may have taken me six hours though.... I did have to drill out the hole in the drivers side of the bumper. Easy to do with a 1/2 drill bit and even did it with a 12v dewalt drill by just going at it slowly. The hitch is on and it’s sturdy. Seems like it’s going to be difficult to get off if ever needed. For instance if you’re going with an aftermarket bumper later. But I enjoy the stock look of the Jeep and the versatility of the front hitch is more important than aesthetics. There is another front hitch mount that curt makes. I mistakenly ordered that one first and then returned it as I didn’t realize it was specifically for the Rubicon with a different front bumper. It also uses different holes and mounts lower than this model. So something to keep in mind.

Scritto da: nycamper

Review applies to 2015 JKU..

Have a 2015 JKU. First the hitch is nice, nice paint job, heavy duty for the price I guess you cant beat it. Ok now to the bad. First, the instructions are horrible do not go by the instructions. except the part that says torque the bolts to 110Ftlbs. Follow that part, The youtube video on the installation from Curt doesnt tell you that they are NOT using a 2015 JKU and therefore you will have to drill out the bottom hole on the drivers side. It also doesnt tell you that the brake booster is in the way, but you can work around it. If you look into other videos they recommend removing it. Problem is that there are 2 bolts that have to be removed and they are only accessible from the top, so you also have to remove the Grille. ( not a huge deal but yeah time consuming.) So to install you have to remove the airdamn ( I didnt have mine in cause I had an aftermarket bumper and winch already installed which actually makes it easier. I also didnt remove the brake booster, I was able to get a ratchet with an extension and the 19mm socket in to tighten it. you need at least an 8" extension and it is pretty difficult but take your time. The lower hole on the driver's side needs to be drilled larger. I was able to do this with a 1/2" step up drill bit and it was quite easy, but be careful not to damage the brake booster pump. Once you do that, you can use the fish wire to put the bolts through each hole, after that its a breeze. Overall I like it, Im not towing anything from the front, only bought it to carry a basket which will hold some fishing poles and a cooler at most. NOTE- If you're not good with tools and/or do not have tools, dont try this. Better off getting a mechanic to install it. If this is the case you shouldnt own a JK anyway.. lolol good luck

Scritto da: Tony D

It's a hitch

2017 jk wrangler unlimited sport. I would have given 5 stars except Curt still hasn't fixed the bold misalignment problem for the drivers side bolt holes. Also, the directions are piss poor so if you don't have some decent amount of ingenuity or mechanical background this may take you more than the one hour it took me. Removing the grill, top bumper plate (drill center of plastic anchors (2) out and buy simple replacements from NAPA), and pump that sits behind the bumper makes things easier. Also the skid plate. Note; if you want the skid plate back on the vehicle it will require some cutting. The skid plate comes off easy with simple POP clip anchors. Same with the top section of grill. The bottom of the grill has push-clips that you release with a bit of force when pulling the grill forward. There are two bolts that mount under the bumper with bolts and anchor plates under the nuts. There are 4 bolts (2 per side driver/passenger) that mount to frame rail. The bottom bolts get the rectangular anchor washer, the top bolts get the nut with extension attached. The only real problem I had was the same as mentioned in nearly every review. The drivers side bolts do not quite line-up. I used a floor jack to force the hitch up enough to get the top bolt in driver side. No such luck with the bottom. It required a 1/2 drill bit and a little widdiling. Not very hard to do and easy to get to but still annoying.

Scritto da: Ralph Hall

Great product

Very good fabrication quality, excellant fit on the vehicle

Scritto da: Danny S.

It’s a hitch!

Quality hitch. Instructions are a bit lacking. YouTube is your friend.

Scritto da: benoit cloutier

Simple à installé

Bon produit