Momentive RTV103 silikoon, üheosaline, must, 300 ml kassett

Name: Momentive RTV103 silikoon, üheosaline, must, 300 ml kassett
Brand: Momentive
SKU: 0779008003305
Price: 57.18 EUR
Availability: InStock

Brand:Momentive

3.9/5

€
57.18

Üldotstarbeline üheosaline silikoonhermeetik, mis kõvastub toatemperatuuril õhuniiskuse toimel sitkeks, vastupidavaks ja vetruvaks silikoonkummiks. Standardse tugevusega pasta konsistentsiga toode, mida saab kanda vertikaalsetele ja ülapealsetele pindadele, kus valatavad/isetasanduvad hermeetikud ei ole otstarbekad. Sellel on suurepärane jõudlus madalal ja kõrgel temperatuuril -75° kuni 400°f. saab kasutada toiduga kokkupuutuvates rakendustes, kus kehtivad FDA määrused, viide: Cds4319. tunnustatud UL poolt UL faili e-36952 alusel.

Summa

Lisa ostukorvi Osta kohe

EAN: 0779008003305

Kategooriad Tööstus ja teadus, Adhesives, Pitser- ja määrdeained, Silikoon,

Vastab sõjaväe spetsifikatsioonidele mil-a-46106 ja nsf standardile 51, on fda 21 cfr 177.2600 ühilduv, USda-ühilduv ja sellel on ul tunnustatud komponendid. Pidev teenindusvahemik on -75 kuni +400 kraadi f (-60 kuni +204 kraadi c) ja katkendlik teenindusvahemik -75 kuni +500 kraadi f (-60 kuni +260 kraadi c). Nakkub paljude metallide, klaasi, keraamika, silikoonkummi ja mõne jäiga plastiga ilma kruntvärvi kasutamata. Pasta konsistents võimaldab kanda vertikaalsetele või pea kohal olevatele pindadele. Üheosaline pasta konsistentsiga must rtv silikoonhermeetik kuni 1/4-tolliste tühimike või pragude täitmiseks ja tihendamiseks.

Country of Origin	USA
Item model number	RTV103-300ML
Manufacturer	Momentive
Package Dimensions	11 x 1.5 x 0.94 inches; 10.41 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: Wakawaka

Actual silicone is great, packaging no so much

So far I’m in for 7 tubes of this stuff and have had the same issue to varying degrees with all tubes. The plunger bypasses a ton of the silicone! Not only have I lost about 5-10$ worth of product every tube but my electric gun is a MESS. Yes I used a manual version too, and tried adding a fender washer to make sure I was supporting the entire plunger - same issue. I did cut my tips small and noticed that going slow reduced the loss but it shouldn’t be happening at all. Initially the directions fail to mention that you must puncture the inner seal after cutting tip. Not a big deal but threw me for a loop right off the bat because normally only cardboard adhesives have the seal and these tubes are plastic. Actual silicone is great quality, using it for fish tank stuff. I had success bonding acrylic to glass (over flow and sump building) and injecting it to reseal a stupid craigslist tank. One thing to note, if you’re using tape at the seam which you plan to remove while the silicone is still wet to get a clean line, you need to pull it off right after completing the seam. If you wait the typical 5 mins you’ll risk pulling the silicone OUT of the seam with the tape instead of just the excess that ran onto the tape.

Scritto da: ScottH

Sets up pretty quickly

It does grow a skin pretty quick, so you don't have heaps of time to get your bead looking the way you want. I found it stuck a little to the blue tape I was using as a mask. Not a big deal, but be prepared for it.

Scritto da: James daniels

This is what you want for fishtank's also, its black!

This is the best on the market for its application in fishtanks, its wayyyy better than silicone. Worth the expense. Just repaired a 3500 dollar fishtank i bought for 300 bucks with it.

Scritto da: I Buy Too Much

Works Like A Charm!

I chose this item due to the reviews regarding fish tanks. Had to reseal used bow front tank. Used frog tape to make perfect bead lines. Go slow by steady your caulk gun to get one continuous bead. Cut the caulk top to the size of bead you want to achieve. Do one pass with wet finger. Don't use a dry finger!!! Then do not touch it! Have wet paper towels ready as it can be messy. After drying I used a scraper to get off any random caulk. Do not scrap any part of aquarium side/bottom seal.If you made it messy, leave it. You do not want to break the cured seal. I waited until the vinegar smell was gone (about 40 hours as my tank was in garage) to rinse out and set up. Awesome product!

Scritto da: Brent Custer

Perfect

Caulking was perfect no hard spots. Great product and will buy again for sure

Scritto da: Bill

Used it to seal a 26 gallon tank worked excellent

Used it to seal a 26 gallon tank worked excellent

Scritto da: Tom Dehnert

Very strong aquarium safe

The best stuff period for redoing the inside of a fish tank

Scritto da: Mike jones

The best stuff around for Aquariums

Very strong, and very fast drying. Used it to repair damaged seals in a Waterbox rimless aquarium.