MG Chemicals 9410 1-osaline elektrit juhtiv liim piiramatu tööajaga kuni KUUMJÄVENDAMISEKS. Kõrge TG, 3mL jaotur Uus valem

Name: MG Chemicals 9410 1-osaline elektrit juhtiv liim piiramatu tööajaga kuni KUUMJÄVENDAMISEKS. Kõrge TG, 3mL jaotur Uus valem
Brand: MG Chemicals
SKU: 0779008941034
Price: 93.36 EUR
Availability: InStock

Brand:MG Chemicals

2.1/5

€
93.36

9410 on elektrit juhtiv, hõbedaga täidetud üheosaline epoksüliim. See on sile, tiksotroopne, ei vaju ja haakub hästi paljude erinevate ainetega. Sellel on toatemperatuuril piiramatu tööiga. Tähelepanu! see toode tuleb kuumtöödelda. See toode võib luua elektrit juhtivaid sidemeid, kus jootmine ei ole võimalik, näiteks kuumatundlike komponentide, klaasi, pehmete metallide või juhtivate polümeeridega ühendamisel. See toimib hästi ka pooljuhtpakendites, mikroelektroonilistes kinnitustes ja kaane tihendamises ning väikeste kiipide, LED-ide ja dioodide stantsina. See ei vaja segamist ja seda saab hõlpsasti kasutada käsitsi, pneumaatilistes ja robotilistes doseerimisprotsessides. 9410 on loodud kõrge TG-ga. Madalama TG jaoks kasutage 9400.

Summa

Lisa ostukorvi Osta kohe

EAN: 0779008941034

Kategooriad Tööstus ja teadus, Adhesives, Pitser- ja määrdeained, Epoksiid, Epoksüliimid,

Soojusjuhtivus 1,1 W/(m·K). Tg 96 °C [204,8 °F]. Kõlblikkusaeg: kuni 4 kuud temperatuuril 25C. Külmutatud = 1 aasta. Ainult kuumtöötlus. Minimaalne kõvenemistemperatuur 90 °C [194 °F]. Takistus 1,8 x 10-3 Ω·cm.

Brand	MG Chemicals
Color	Silver Grey
Compatible Material	Glass
Country of Origin	Canada
Item Form	Chips
Item model number	9410-3ML
Manufacturer	MG Chemicals
Material	Silver, Epoxy
Product Dimensions	1.01 x 8.06 x 1.01 inches; 0.33 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: Fred E. Elum

No Instructions Included

I bought this for a project that I was unsure if I could heat. I did not want to use my low temp solder. When it arrived there is paper in the packaging, but no instructions. I found the TDS on the manufacturer website. It must be heated to activate the epoxy. Higher temperature give shorter cure time. If this information were in the description I would not have purchased. Curing is between 90C-120C for 60-7 minutes. My low temp solder activates at about 125C, so it is little benefit. It does not have any adhesion until cured. It did not run , but it did not hold the pieces together until I could heat it. It has a very distinct formaldehyde odor when curing. Don't breathe the vapors. UPDATE Jun 2021: It seems to work as intended. Additionally, the seller seems to have updated the listing and information to include that it must be heat cured. That information was not present when I bought it. At over ten bucks a gram instructions should be provided....

Scritto da: Scott

HEAT Cured Only!

The title for this product should be much more explicit - this adhesive requires a minimum of 70 degrees C/158 degrees F to cure.

Scritto da: Dawn

Dried up

For the money spent on a small market product that you can not find readily you would expect it to show up in working order. It was USELESS as it had gone bad probably years ago and was sitting on a shelf till the next poor sap ordered it. Please read all the reviews and do not buy this trash. Now I have to ship it back to get my money refunded. What a huge waste of time.

Scritto da: Ray

EPoxy

Make sure you wear protective gloves.

Scritto da: Guillermo Hernandez

Does not work at all

I applied 80C temperature for 30 minutes and it does not dry and will not bond at all. It is not like shown in the video, it is like a paste that is difficult to apply. I have tried this product three times and it is the same results. Another Chinese useless product?

Scritto da: Behnam

Great dispensing quality

This product is very easy to dispense and use. No mixing is required and it is very conductive too.

Scritto da: Adrian T.

Arrived fully cured and unusable

The shelf life of this product is not unlimited and it had clearly expired or been stored in an environment that was too warm. It was fully cured and unusable. It did not ship with any certs or expiration date documentation so who knows how old it was. I bought the two-part system to replace it because the shelf life is much longer than the one-part

Scritto da: Amazon Customer

Awesome stuff!

Works awesome, used to bond aluminum wires to copper pad. Worked perfectly.

Scritto da: Rick Barnier

No good

Went to use the product for the first time and it was all dried up on the inside. Lost a customer due to this.

Scritto da: thomas

dans l os

texture pas fluide et pas moyen de la faire catalysé malgré 2h a 80°