Andurilüliti MSX12 M4 360-kraadine mitme kinnitusega hõivatuse andur, valge

Brand:Sensor Switch

3.1/5

79.76

Reguleeritav viivitus, eelseadistatud 15 minutile. Töötab LED- või luminofoorlampide, ribavalgustite ja ümbritsevate valgustitega. 360-kraadine passiivne infrapunatehnoloogia tagab liikumistuvastuse põranda tasandil kuni 60 jala kaugusel. Valge akrüülkorpus sobib valgete valgustitega. Pakub automaatset sisse- ja väljalülitamist ühe või mitme seadme jaoks energiasäästu ja mugavuse huvides.

Reguleeritav viivitus, eelseadistatud 15 minutile. Töötab LED- või luminofoorlampide, ribavalgustite ja ümbritsevate valgustitega. 360-kraadine passiivne infrapunatehnoloogia tagab liikumistuvastuse põranda tasandil kuni 60 jala kaugusel. Valge akrüülkorpus sobib valgete valgustitega. Pakub automaatset sisse- ja väljalülitamist ühe või mitme seadme jaoks energiasäästu ja mugavuse huvides.
Batteries Included? ‎No
Batteries Required? ‎No
Color ‎White
Country of Origin ‎China
Customer Reviews 4.1 4.1 out of 5 stars 44 ratings 4.1 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item model number ‎MSX12 M4
Item Package Quantity ‎1
Item Weight ‎5.6 ounces
Manufacturer ‎Sensor Switch
Part Number ‎MSX12 M4
Power Source ‎AC
Product Dimensions ‎4.13 x 4.13 x 2.5 inches
Warranty Description ‎5 years

3.1

8 Review
5 Star
56
4 Star
20
3 Star
9
2 Star
6
1 Star
8

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega*

Scritto da: Jeff Hammer
Wiring not easy
NOTE: If ballast disconnect plugs are cut, white wire with red stripe is Neutral. Cap off plain white wire." I listened to that instruction, capping off the plain white wire (in the set of three). However, the light would not work with that wire out of the equation. I ended up having to wire both the white wire and red-stripe white wire to the ballast's white wire. Then it finally worked! I read in one of the other reviews that someone else had to do this. So beware of this note in the instructions.
Scritto da: Ranger Rick
Seems to work OK. The installation information is OK ...
Seems to work OK. The installation information is OK but the programming instructions are awful. I found these details instructions online. Time Delay Program Instructions 1. Push and hold button until LED flashes rapidly (approximately 6 seconds). Release button. 2. Press button twice to enter Time Delay adjustment mode. The LED will flash back the current Time Delay setting according to below table (i.e. 5 flashes for 10 minute Time Delay). 3. Wait approximately 3 seconds 4. Press button the number of times for the desired setting (i.e., press twice for 2.5 minutes Time Delay). 5. LED will flash back this new setting, (repeated up to 10 times). Press button down again until LED flashes rapidly (approximately 6 seconds). Release button. 6. Press button twice to verify Time Delay has been reprogrammed. LED will flash back twice indicating acceptance of new setting Time Delay Settings Table Push Button the number of increments desired 1 ~ 30 Sec 2 ~ 2.5 Min 3 ~ 5.0 Min 4 ~ 7.5 Min 5 ~ 10.0 Min 6 ~ 12.5 Min 7 ~ 15.0 Min 8 ~ 17.5 Min 9 ~ 20.0 Min
Scritto da: Stan
great motion sensor
Easy to install and program, would buy again. Had it for 5 months and no problems. Installed in our pantry for the light and couldn't be more please,no more pull chain to deal with.
Scritto da: Christy Holter
Works great, very sensitive.
Works great even for a low ceiling but is extremely sensitive.
Scritto da: Anchorman-CET
It has worked for 2+ years
I bought this in October 2018. It has worked flawlessly for all this time. Like so many others my only complaint is the instructions. I shiver with dread anytime I think about changing the shut-off timer. Regardless, it's been very reliable thus far.
Scritto da: William Carson
bettb
This works great. I had to modify the installation because I used it on flush mounted fluorescent lights that could not be accessed from the end where it was intended to be mounted. Mounted it on the inside corner and cut a square out of the lens so the cover can be lowered to replace the bulbs. Works great. The next on I get will be able to install it as intended because they will be surface mounted lights.
Scritto da: Joe Donnelly
Works as advertised
Had my electrician install it. He likes it, I like it. It works great. Going to buy a second one
Scritto da: Amazon Customer
Four Stars
Is working well for fixtures in a shop!

Seotud tooted

hot
Lutron Maestro liikumisanduri lüliti
3.7/5

€ 69.85

Lutron Maestro liikumisanduri lüliti
3.7/5

€ 69.85

Avastage meie rahvusvaheline võrgustik

Saadame 28 riiki, üle 200 000 toote. Olge kursis, tellige uudiskiri.

Array