Rain Bird 12DSH topeltpihustusotsik, 180° poolring muster, 9'–12' pihustuskaugus poolring 180° muster 180° poolring

Brand:Rain Bird

3.7/5

23.24

TOOTE KIRJELDUS Rain Bird 12DSH topeltpihustus, 180° poolringi mustriga sobitatud sademenormi otsik, reguleeritav 9' kuni 12' pihustuskaugus, 23° trajektoor. Sellel spetsiaalsel otsikul on kaks pihustusava, mis parandavad tihedat kastmist ja ühtlasemat veejaotust. Unikaalne patenteeritud alumine disain lühendab kastmisaega, kasutab 30% vähem vett ja vähendab vee raiskamist tuulistes tingimustes. Pea lähedal olevad alad kaetakse ühtlaselt, minimeerides kuivad pruunid laigud. Mittesöövitav plastikust ja roostevabast terasest konstruktsioon tagab pika eluea. roostevabast terasest reguleerimiskruvi reguleerib voolukiirust 1,8–2,6 gallonit minutis ja pihustuskaugust 9–12 tolli. Kinnitatud kruvipesa hoiab ära kruvikeeraja libisemise reguleerimise ajal. Düüs pihustab 180° poolringi 23° trajektooril ning sobib kõikidele Rain Bird vihmutitele ja põõsaadapteritele. Peene võrguga filtriekraan tagab täpse raadiuse reguleerimise ja kaitseb alumist ava prahi eest. Aastakümneid usaldatud Rain Bird MPR düüsidel on Matched Precipitation Rate veejaotustehnoloogia. Erineva kaare ja raadiusega pihustid saab segada samal tsoonil olenemata pihustamise reguleerimisest ja säilitada ühtlase veejaotuskiiruse. Saadaval on lai valik MPR-düüse, et vee jaotust saaks kohandada vastavalt teie maastiku ainulaadsetele ja mitmekesistele vajadustele. MPR-düüsid on loodud pakkuma ühtlast katvust, tagades, et teie muru on kogu ulatuses roheline, ilma kuivade või pruunide laikudeta. Teised saadaval olevad Dual Spray MPR-düüsid (müüakse eraldi) on järgmised: 360° täis (12DSF) ja 90° veerand (12DSQ) mustrid. Rain Bird „Tootjalt arukas veekasutus Rain Bird Corporation on eraettevõte, mis asutati 1933. aastal California põllumajandusbuumi ajal. Oleme tunnustatud kui 1. niisutustoodete ja -teenuste tootja ja pakkuja maailmas. Müügiesindustega üle maailma; pakume üle 4000 vett säästva niisutustoote rohkem kui 130 riigis. Rain Bird on algusest peale tootnud ja pakkunud tööstuse kõige laiemat valikut kvaliteetseid niisutustooteid farmidele, golfiväljakutele, spordiareenidele, äriarendustele ja kodudele. Viimase 80 aasta jooksul on Rain Bird saanud üle 450 patendi üle maailma. Sealhulgas esimene niisutamiseks 1935. aastal meie algse löökajamiga vihmutiga (USA patent nr 1 997 901), mis muutis põllumajandusliku toidutootmise pöörde ja juhatas sisse uue ajastu niisutamises kogu maailmas. 1990. aastal määras Ameerika Põllumajandusinseneride Selts selle algse löökvihmuti ajalooliseks maamärgiks. Meie tooted hõlmavad kõiki niisutamise aspekte... taimerid/kontrollerid, hüpikpihustid, hüpikpihustuspea vihmutid, vihmutid, niisutusventiilid, tilkniisutus, drenaaž ja palju muud. Need tooted on valitud ja paigaldatud üle maailma suurimatesse ja mainekamatesse elamu-, äri-, põllumajandus- ja golfiväljakute niisutamise projektidesse. Rain Bird on pühendunud vee intelligentsele kasutamisele™, mis ulatub toodetest kaugemale, hariduse, koolituse ja teenusteni tööstusele ja kogukonnale. Meie pärand on projekteerida ja toota ainult kõrgeima väärtuse ja kvaliteediga tooteid. Oleme tänulikud, et oleme saanud paljudelt meie hinnatud partneritelt mitmeid tunnustusauhindu. Vihmalind “Vee intelligentne kasutamine

Valmistatud väga vastupidavatest UV- ja kemikaalikindlatest materjalidest, et tagada pikk kasutusiga. Roostevabast terasest reguleerimiskruvi reguleerib voolukiirust ja pihustuskaugust. Kõrvaldab kuivad pruunid laigud peade lähedal. Ühildub kõigi Rain Bird hüpikvihmutitega. 180° poolringi muster reguleeritava pihustuskaugusega 9' kuni 12'. Kasutab 30% vähem vett; vähendab vee raiskamist tuulistes tingimustes. Kahekordne pihustusotsik tagab suurepärase kastmise.
Brand Rain Bird
Color Brown/Black
Country of Origin USA
Customer Reviews 4.7 4.7 out of 5 stars 276 ratings 4.7 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer No
Item Dimensions LxWxH 0.89 x 0.89 x 2.1 inches
Item model number 12DSH
Item Weight 0.022 ounces
Manufacturer Rain Bird
Material Stainless Steel
Product Dimensions 0.89 x 0.89 x 2.1 inches
Style Pop-Up

3.7

7 Review
5 Star
75
4 Star
20
3 Star
3
2 Star
0
1 Star
2

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega*

Scritto da: Eugene
Better near and far spray coverage
To adjust the spray distance and water output of this nozzle, turn the screw on top counterclockwise for an increase, or turn it clockwise for a decrease. To adjust which direction it sprays, you can remove the top of the sprinkler head and reinsert the nozzle tube. Some sprinkler heads are installed deep enough that pulling the top off is undesirable, so you can pull up the nozzle tube and twist it until it's rotated in the right direction. It should make clicking noises as it is turned. If there's no clicking, then you may be unscrewing the sprinkler from the pipe beneath it, or unscrewing the top of the sprinkler, so I prefer to turn it clockwise. I use this nozzle wherever I don't need an adjustable nozzle because it does a better job of providing even coverage both near and far. It works great wherever my sprinklers pop up high enough, which in my lawn requires at least a 4 inch sprinkler. I have a couple 2 inch sprinklers that don't come up enough, so the dual spray part of this nozzle sprays directly into the grass right next to it. It's not the fault of the nozzle, but a notification that I should swap out that sprinkler head. I've also found that this nozzle can directly replace some of the nozzles on my Orbit sprinklers. My only gripe with this nozzle, and all Rain Bird nozzles, is that the adjustment screw tightness has a lot of variation. Sometimes it's so tight that the nozzle must be pulled up and gripped tightly to adjust it, which results in a face full of water if you try this while the sprinklers are on, but other nozzles are loose enough that they can be adjusted just by turning the screw without holding onto the nozzle. Fortunately giving the adjustment screw a few turns to loosen it up before installing it is all it takes to resolve this minor issue.
Scritto da: Eugene
Good near and far spray coverage
To adjust the spray distance and water output of this nozzle, turn the screw on top counterclockwise for an increase, or turn it clockwise for a decrease. To adjust which direction it sprays, you can remove the top of the sprinkler head and reinsert the nozzle tube. Some sprinkler heads are installed deep enough that pulling the top off is undesirable, so you can pull up the nozzle tube and twist it until it's rotated in the right direction. It should make clicking noises as it is turned. If there's no clicking, then you may be unscrewing the sprinkler from the pipe beneath it, or unscrewing the top of the sprinkler, so I prefer to turn it clockwise. I use this nozzle wherever I don't need an adjustable nozzle because it does a better job of providing even coverage both near and far. It works great wherever my sprinklers pop up high enough, which in my lawn requires at least a 4 inch sprinkler. I have a couple 2 inch sprinklers that don't come up enough, so the dual spray part of this nozzle sprays directly into the grass right next to it. It's not the fault of the nozzle, but a notification that I should swap out that sprinkler head. I've also found that this nozzle can directly replace some of the nozzles on my Orbit sprinklers. My only gripe with this nozzle, and all Rain Bird nozzles, is that the adjustment screw tightness has a lot of variation. Sometimes it's so tight that the nozzle must be pulled up and gripped tightly to adjust it, which results in a face full of water if you try this while the sprinklers are on, but other nozzles are loose enough that they can be adjusted just by turning the screw without holding onto the nozzle. Fortunately giving the adjustment screw a few turns to loosen it up before installing it is all it takes to resolve this minor issue.
Scritto da: Dazzza
Great Replacement at Low Cost
These nozzles fit the 1800 series and UNI-Spray series sprinkler head bodies. They will also fit onto most other brands of sprinklers that use universal female thread nozzles. While Rainbird makes a wide range of nozzles, most are only available at specialty irrigation stores. Hardware stores and home centers tend to only carry a few of the most common nozzles. Rainbird makes a very good nozzle set with good water spray uniformity. Many of them have matched precipitation rates so you can mix different radius and pattern nozzles on the same valve zone without messing up the water application uniformity. Be careful of this as Rainbird's literature calls all of their nozzles "matched precipitation rate", but that does not mean they are all compatible with each other! For example, you should not use a 4 series VAN nozzle on the same valve circuit as a 5 series MPR nozzle. Read the nozzle descriptions for each series of nozzles below for details on which nozzles are compatible. The spray radius can be reduced up to 25% on all but a few specialty bubbler nozzles using a screw on top of the nozzle. Note that the separate screen must be installed under the nozzle for the radius adjustment to work correctly. If you remove or don't install the screen you won't be able to adjust the radius. The screens are provided with the nozzles when you purchase them. All Rainbird nozzles are constructed of high-quality plastic.
Scritto da: Padmapada
Easy fix for a damaged sprinkler head, saved lots of $$$
The folks who cut my grass tend to cut the heads off the sprinklers with their machines. In the past, I've called the sprinkler company to fix them, and ended up paying hefty service calls. This time I had a look and saw that the damaged head simply unscrewed. So I went to the local big box store and tried to find a replacement. The clerk tried to talk me into buying something that had threads on the OUTSIDE because, I guess, that is what he had in stock. But I needed a head with threads on the inside, one that would just screw down on top of the pop-up pipe. I saw this on Amazon and asked other customers if it had threads on the inside, and the answer was positive. So I bought this, and it took about 2 minutes to install. The head is clearly marked so that you can see which way the spray goes (this is a half circle), and there is a screw on top to reduce the diameter if you want. It is installed in the berm, or tree lawn, or verge, or curb strip, or whatever you call that narrow strip of lawn between the sidewalk and the street. Perfect. Good for all dialects.
Scritto da: Cindy
Good product
Product fit as described
Scritto da: Amazon Customer
Performance met the product description.
Did a lot better than the water savors you can buy.
Scritto da: Brenda Brennan
Perfect fit
Perfect to replace broken sprinkler head.

Seotud tooted

Avastage meie rahvusvaheline võrgustik

Saadame 28 riiki, üle 200 000 toote. Olge kursis, tellige uudiskiri.

Array