POWERTEC 73010V 10-osaline karbiidist otstega otsakukomplekt, professionaalne seeria 1/2-tollise ja 1/4-tollise varrega ruuteri otsakute komplektiga, 10 tk

Brand:POWERTEC

3.7/5

€
131.01

Professionaalse seeria karbiidist otsakute (10 tk) komplekti tutvustamineSee ulatuslik 10-osaline komplekt pakub teile kvaliteetset valikut ruuteriotsikuid. Ruuteri otsad on ainulaadse disainiga meie iseloomulike värvikoodiga profiilide ja, mis veelgi olulisem, mikrosüütelisest karbiidist peadest kiiremaks ja ülitäpse puidu lõikamiseks ilma sidumiseta. Universaalsed profiilid ½ tolli ja ¼ tolli varrega, mis sobivad kõikidele suurematele ruuteritele (Boschi jaoks, DeWalt, Makita, Milwaukee, Porter Cable, Ryobi & Black & Decker) Teie mugavuse huvides on ruuteri bitid korralikult pakitud ja hoiustatud kaasasolevas luksuslikus hoiukastis. Sellel hoiukarbil on läbipaistev akrüülist ekraaniplaat ja tahke must akrüülalus koos vahust ruuteri otsikualusega, mis võimaldab hoida oma otsikuid kindlalt ja korras. Sisaldab (üks igast): Corebox R1/8” x ¼” V-Groove 90 kraad ½" Roundover R3/8" x 5/8" Roman Ogee R1/4" x 21/32" kaldenurk 45 kraadi 13/32" tasapinnaline trimm ½" x 1" sirge ¼" x ¾" sirge ¾" x 1- 1/4-tolline tuvisaba ½” x ½” süvis ½” x ¾” Deluxe-hoiukohver 8,5” x 3,5” x 4,33” (8,5” x 3,5” x 1,25” põhi) Võrreldes tavaliste terasotsadega, on need karbiidist lõikavad tööriistad on palju tõhusamad ja tõhusamad – aidates vähendada puidutöötlemismasinate koormust. Need tagavad puhtamad ja sirgemad lõiked ning nõuavad vähem teritamist kogu oma muljetavaldava eluea jooksul. Need omadused koos on mõeldud teie töövoo suurendamiseks, pakkudes samal ajal professionaalseid tulemusi. POWERTEC on juhtiv kvaliteetsete puidutöötlemistööriistade ja -tarvikute, masinate ning originaalseadmete tootjate varuosade valiku tootja. Oleme pühendunud ootuste ületamisele, tuues samal ajal tööstusesse uusimaid uuendusi, tehnoloogiat ja tootearendust.

Summa

Lisa ostukorvi Osta kohe

EAN: 0843441120360

Kategooriad Tööriistad ja kodukaubad, Elektri- ja käsitööriistad, Elektritööriistade osad ja tarvikud, Rullimasinate osad ja tarvikud, Router Bits, Kõrvapuurid ja sooned,

SÄILITAMISEKOHT: hoidke oma karbiidiotsikuid meie luksuslikus korduvkasutatavas hoiukarbis. Nii läbipaistev ülaosa kui ka must põhi on valmistatud akrüülist. KARBIIDKALTUGA: annab peadele suurema kõvaduse, mis võimaldab neil säilitada lõikeomadused, töötades samal ajal kauem ilma uuesti teritamiseta. FUNKTSIOON: see täielik ruuteri otsikute komplekt sisaldab kõige populaarsemaid profiile (sirge, trimmitud, tihvtisaba tisleritööd ja dekoratiivsed äärised), mida professionaalid kasutavad mitmesugusteks freesimiseks, puidutöötlemiseks, ääristamiseks, trimmimiseks, soonimiseks ja muuks. PREMIUM DISAIN: igal otsal on tasakaalustatud konstruktsioon ja disain, mis vähendab oluliselt tagasilööki ja võimaldab minimaalset vibratsiooni puhta ja ülitäpse lõike ja trimmimise jaoks. 10 tk komplekt SISALDAB: Corebox R1/8” x ¼”

Batteries Required?	‎No
Country of Origin	‎Taiwan
Customer Reviews	4.7 4.7 out of 5 stars 595 ratings 4.7 out of 5 stars
Included Components	‎Corebox R1/8” x ¼” \|
Item model number	‎73010V
Item Package Quantity	‎1
Item Weight	‎2.61 pounds
Manufacturer	‎POWERTEC
Material	‎Wood, Alloy Steel
Part Number	‎73010V
Product Dimensions	‎11.81 x 4.92 x 6.11 inches
Style	‎Router Bit Set, 10pc

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: Prime Lover

Smells Like Cancer

It could probably be $5 cheaper, but it beats what I was going to do getting rubber bushings/grommets and putting them in wood. Wood looks nicer, but it would have ended up costing like 3x as much plus the work lining everything up neatly etc. Some people are foolish and don't understand that you won't be able to use EVERY hole considering oversized/large bit heads... My only gripe is that it's been open for like 5 hrs and is still radiating this horrific Chinese factory smell. I feel bad actually knowing that people are enduring this right now to make this foam. It smells cancerous and hopefully gone tomorrow. Minus 1 star for putting me through this smell and mental guilt thinking about the horror people experience making it

Scritto da: Jonathan Kar

Organization at its finest

I purchased this Router Bit Tray to help in organizing my Router Bits. This Tray has made the organization of my Router Bits much more convenient! I now know exactly where they are and can easily access them when I use them! Great product!!! Great Design!!!

Scritto da: Smells really bad!!!

Smells like cat's pee

Smells really bad!!

Scritto da: Eric

Not all your bits will fir well

I ended up cutting it into sections for different things

Scritto da: Leo R Graywacz

Holes are a little tight, tough to push them in more than 1/2" deep.

I would have liked to of pushed the shafts of the bits in farther but they are a bit tight. It still supports them fine. If you want to store lots of 1/2" shank straight/flush cutters the spacing is ideal. But if you have profile bits the hole spacing is a bit close. The 1/4" holes are spaced pretty good as the OD of most of the bits aren't that large. But some of the 1/2" bits the OD is large enough where they touch each other or you have to go every other hole. If they lost 2 1/2" holes per row it would be better for spacing of the 1/2" bits, it wouldn't look as pretty as the holes wouldn't all line up but it would be more practical (for my collection). Or maybe a row or two of wider spacing for the profile bits and the existing spacing for straight/flush bits. The foam is pretty stiff but still slightly flexible. It had a slight smell when I took it out of the packaging. No labels on the foam, just on the outside of the plastic wrapper. After I put all my bits in I was surprised at how many I had collected over the years.

Scritto da: D. Morreale

Better than expected.

I was impressed with how sturdy this is. It also lets you pack a lot of bits into a small space. I'd tried making router bit racks out of wood on my drill press, but when I drilled holes with a 1/2" bit they were too tight and the router bits wouldn't fit, so I drilled them out again with a 9/16" which made them too loose and the router bits would wobble around. At that point I figured rather than spending the money to buy a 17/32" Forstener bit to try it again, I'd just give this a try, and I'm glad I did. The bits fit snuggly and don't wobble around at all, but they still go in and out easily. I plan to build a drawer to fit the tray's dimensions. Eventually, when the Router bit collection outgrows this tray, I will definitely get a second one. It might be worth mentioning, this does have a strong smell. You know that foam-plastic chemical smell? It doesn't bother me so I didn't take a star away, but I know it bothers some people. I stopped noticing it after a week or two.

Scritto da: WilliedaFish

All of my bits are now in one place.

All of my bits fit in this handy foam square. I suspect that won't always be the case; but, for now, there is ample room for both 1/2" shank and 1/4" shank bits. Incidentally, because I have both size bits, it would be handy if there were room on this doodad to store the extra collet that I install on my router table to use one or the other size. What that suggests, though, is that I really should build a cabinet with a drawer to house this tray and other drawers for accessories like the extra collets, collars, inserts and the like.

Scritto da: Steven

Great way to organize your router bits

I got tired of dealing with the little plastic cases that Freud router bits come in, they take up space, are a pain to remove and insert the router bits. This foam block consolidates all my bits into one spot thats easy to insert and remove. I like how it supports 1/4 and 1/2 inch shanks, the price is very reasonable for what you get and a lot quicker than drilling plywood to create something similar. I can insert all my router bits and pick the tray up because it securely holds the bits in place, you could even tip it over and bits wont move.

Scritto da: Eiffel

Good storage solution for 1/4", 8mm and 1/2" router bits

This is a simple yet effective way to store a fairly large collection of router bits... It holds well 1/4", 8mm and 1/2" bits -I don't have any 12mm bits to test. The spacing between the holes is fairly tight, which means it might not be possible to use every hole when using large diameter bits. The foam is fairly thick and seems to be of good quality, stiff but with enough give to insert and remove the bits easily, while holding them well. Overall the tray is a very tight fit in a Systainer -cutting the foam is strongly recommended if this is what you have in mind! I understand that holding the bits in foam is better than holding them in a wood block from a corrosion perspective, but I only started using this product a few weeks ago and can't confirm this yet.

Scritto da: Paul

Foam router bit storage- great value!

Great value router bit storage! Fits both 1/2 & 1/4” bits for drawer or storage box.

Scritto da: BlacksMYTH

Best thing ever

This is brilliant. easy to fit 1/4 and 1/2 inch shaft router bits. just happens to fit in my drawer but would be easily cut to fit into a smaller one. great bit of kit to organize your tools.

Scritto da: Aga

Five Stars

Present for my husband. He was trilled, bits finally safe and sound.

Scritto da: C. Mason

High quality foam, but very tight fit!

Generally happy that I bought this router bit tray as it looks nice, is made of very durable and dense foam, and offers a lot of storage. Only downside is how tight the fit is on router bits. With this in a drawer I didn't need it to be extremely tight fitting, if you're mounting this on the inside of a door it'll certainly work!