NEIKO 10194A titaanist astmeline puur, ülikiire legeerterasest otsak, puu- ja metalliaugulaiend, 10 astmeline suurus 1/4 tolli kuni 1 3/8 tolli 1/4-1-3/8 puur

Name: NEIKO 10194A titaanist astmeline puur, ülikiire legeerterasest otsak, puu- ja metalliaugulaiend, 10 astmeline suurus 1/4 tolli kuni 1 3/8 tolli 1/4-1-3/8 puur
Brand: Neiko
SKU: 735090625498
Price: 39.63 EUR
Availability: InStock

Brand:Neiko

3.4/5

€
39.63

Meie Titanium Step Drill Bit võimaldab teil teha täpselt sellise suurusega augu, mida vajate mis tahes projekti jaoks teie kodus või töökohal. Sellel metallist augulõikuril on 135-kraadine poolitatud ots ja 2 soonega konstruktsioon, mis läbib peaaegu iga pinna, sealhulgas terase, puidu ja muude materjalide. See on konstrueeritud koonusekujulisena, et ühe lihtsa sammuga automaatselt koputada, puurida ja eemaldada auke. Meie astmeotsak on valmistatud kiirest legeerterasest ning sellel on titaannitriidkate, mis tagab vastupidavuse, pikema eluea ning jahedama, kiirema ja puhtam puurimine. Kasutamiseks asetage otsiku ots vastu metallilehte või puitplaati, millega töötate, ja puurige soovitud mõõtu. Pole vaja osta mitut otsikut, kui saate töö tehtud ühe lihtsa puuriga. See metallile mõeldud astmeline puur võib puurida järgmises suuruses auke: 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/8, 1 1/4 ja 1 3/8. Meie kiiret puuri saate kasutada terastöödeks kodus või tööl ning selle väike suurus võimaldab teil selle tööriistakasti pakkida ja kõikjale kaasa võtta. Ükskõik, kas vajate roostevaba terase lõikamiseks multifunktsionaalset puuri või uut astmelist puuri, mida oma seadmetele lisada, on NEIKO meie vastupidavate, töökindlate ja tugevate tööriistadega teie selja taga.

Summa

Lisa ostukorvi Osta kohe

EAN: 735090625498

Kategooriad Tööriistad ja kodukaubad, Elektri- ja käsitööriistad, Elektritööriistade osad ja tarvikud, Ehituspuuride osad ja tarvikud, Puuriplaadid,

RASKE PUUR: Meie multifunktsionaalne puur on loodud töötama mis tahes projektiga, olgu see suur või väike. Saate seda kasutada uute aukude puurimiseks või olemasolevate suurendamiseks ilma puuriterasid vahetamata. Tehke oma töö enesekindlalt ja kiiresti! MITMESUGEV PUUR: sellel augupuuril on kerge loetavuse huvides otsale graveeritud 10 erinevat suurust. Sellega saab puurida järgmises suuruses auke: 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/8, 1 1/4 ja 1 3/8 . KARASTUNUD TERASE PUUR: kasutage seda terasest puuri terase, puidu ja muu paksu metalli puurimiseks. Sellel on 135-kraadine poolitatud ots ja kahe soonega spiraalne disain, mis eemaldab automaatselt ja laiendab auke puhtama puurimisprotsessi tagamiseks. MITMEKÜLGNE PUUR: see multifunktsionaalne spiraalne puur sobib kindlalt enamiku püstolitrellide, puurpresside ja muude käsitsi elektriliste tööriistadega. Kasutage seda mitmekülgset väikest koonusekujulist puurit metalli- ja puiduprojektide jaoks tööl või kodus. KÕRGE KVALITEETNE PUUR: meie titaanpuur on valmistatud kiirest legeerterasest #4241 ja sellel on titaannitriidkate, mis tagab suurema vastupidavuse. Kahe flöödiga disain teeb sellest otsast kiire ja kauakestva metalli lõikamise tööriista.

Assembled Diameter	‎0.25 inches;1.375 Inches
Batteries Included?	‎No
Batteries Required?	‎No
Brand	Neiko
Brand	‎Neiko
Color	‎Titanium
Customer Reviews	4.4 4.4 out of 5 stars 7,361 ratings 4.4 out of 5 stars
Cutting Angle String	135 Degrees
Cutting Angle String	‎135 Degrees
Cutting Diameter	‎0.25 inches;1.375 Inches
Finish	‎Titanium Nitride
Finish Type	Titanium Nitride
Finish Type	‎Titanium Nitride
Included Components	‎Titanium Step Drill Bit Set
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	‎6.1 x 2.9 x 1.6 inches
Item model number	‎10194A
Item Package Quantity	‎1
Item Weight	‎5 ounces
Manufacturer	‎Ridgerock Tools Inc.
Material	High Speed Steel
Material	‎High Speed Steel
Measurement System	‎Inch
Minimum Bore Diameter	‎0.38 Inches
Part Number	‎10194A
Pattern	‎Drill Bit
Product Dimensions	‎6.1 x 2.9 x 1.6 inches
Shank Type	3-Flat
Shank Type	‎3-Flat
Size	‎1/4” to 1-3/8”
Style	‎1/4"-1-3/8"
Surface Recommendation	‎Aluminum,Copper,Plastic,Stainless Steel,Steel
Tool Flute Type	‎Spiral

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: Salar de Uyuni

I used it as a grinder to remove power steering pulley.

It did what I intended. The oulley was frozen onto power steering shaft. I had to gring it off!

Scritto da: T.T.

works for what I need it for

I use this bit generally for plastic (ABS, UHMW, and HDPE mostly). It cuts cleanly and effortlessly. I had purchased one in a smaller size about 5 years ago and used it daily but the last straw for that one was cutting a 3/4" dia hole in 409 Stainless steel. Stainless is hard on bits, that one included. I wouldn't recommend it for that type usage. Aluminum is fine, I have cut plenty of aluminum with it. Mild steels are generally ok to cut too so long as you use PLENTY of lubricant and keep the heat to a minimum. Please note that your cutting speed will have to reduce when you cut larger holes, the heat will destroy the bit and sometimes the part if you try to drill too fast or feed it into the work piece too quickly.

Scritto da: Stewart

Works great

It worked great for drilling a 1 1/4 inch hole in my grill so I could install a silicone grommet for temperature probes.

Scritto da: Troy D.

Specialty bit

I needed to enlarge an existing hole in a stainless steel sink for a dishwasher air vent. Using a conventional hole saw was not going to work as I had no center. This was the perfect bit for the job. I just used some light water, and sprayed the bit as I drilled. I was getting metal shavings, so I can say the bit was cutting, not just burnishing. I used a fairly slow speed on a half inch drill. Worked perfect for my application. Do I think this bid could drill holes all day long in stainless? Absolutely not. If you have a few holes to do though these are probably a good value. I'm sure I can get a few more uses out of this as I only used one size. There's plenty of times where I need to enlarge a hole as I was off the first try, and these bits are really idea for enlarging an existing hole. I can't think of any other bit that would work as well. It's kind of like an EZ-out. When you need it there's not much else that works as well, and I think that's the case for this bit. For me, it was the perfect solution.

Scritto da: Lance Moreno

Easy to use, versatility, all in one

Used it on a plastic Scepter water container. Ease of use, easy to control, multi-purpose .

Scritto da: Gary R.

Does the deal; a bit pricey

Take it slow, allow the bit to cool, and pay attention to which depth gauge you are on. Does a nice cut

Scritto da: GB

Awesome bit!

Received this bit a few days ago and used it yesterday to drill 6 holes into a thick tractor bucket. First time using a step bit. Used cutting oil as recommended and had zero issues. Went slow and allowed the tool to do the work. Flawless! And it’s still as sharp afterward as it was at the beginning. Very pleased!

Scritto da: The_Phantom

Works, but is not smooth . . .

I bought this so I could put a new grommet into my Weber Smokey Mountain Smoker. My model was an older model and didn't come with the grommet that allows for temp probes to pass through and monitor the temp of the inside of the smoker and the meat being smoked. When I purchased the grommets (it came 2 to a pack), Amazon recommended this drill bit for making the hole in the smoker to allow for mounting the new grommet. I already have a drill bit like this one from a name brand, BUT it wasn't big enough to accommodate the grommet I was purchasing. So, since I needed this to make my project work and since it was about 25% of what I paid for my other one, I bought it. Also, I factored in that I was probably only going to need to use it once, ever, so it made sense to get this product at the same time of purchase as the grommets. When the grommets and drill bit arrived, I was pleased and excited. I cleaned up the outside of the smoker where I was going to drill and then put some painters tape over the designated spot to try and prevent the enamel from chipping. I then started to drill. The tape seemed like a good idea at the time, but the tape quickly peeled and got stuck in the drill bit. I eventually pulled the tape off completely about 1/3 of the way through for drilling. I needed to make a hole that is 1 and 1/4" in diameter, which was the second to last step on the bit. I was trying not to go too fast 'cause I was worried I would get overzealous and drill the hole too big and then I'd be Really Mad 'cause I would have messed up my smoker. So I took my time and kept on going. When I got about 3/4 of the way through, the bit was not very smooth - not like my other name brand bit. I was getting even more scared that I was going to mess up my smoker and it was making me nervous using this drill bit. However, I had already come this far and there was no turning back at this point. So, I pressed on, but gently. The biggest problem I was encountering was that the bit would catch on the opening it had created with each step that it passed through on the bit and I had to be careful not to cut my fingers, mess up my drill or mess up my smoker. It was frustrating because it wasn't a smooth drilling process at all. However, I eventually got to the stopping point and took the bit out. I could see a nasty burr of sharp metal hanging from the opening I had just created. So I put the drill on the other side of the hole and very gently drilled from that side just long enough to get rid of it and make the opening fairly smooth. Then, I was finally able to install the grommet and breathe a sigh of relief that I had not messed up my smoker. I share all of this with you, the reader, to let you know that this product did work, BUT it was not very smooth and if the name brand bit I had was big enough, I would gladly have used it instead. Knowing what I know now, I would caution you on purchasing this and remember my experience with this drill bit. It Can do the job, but you have to be super careful with it, or you might mess something up that you can't fix later and that would be very, very bad, I would imagine. I give this product 3/5 stars, because it did do the job and the price was nice, but you get what you pay for and you definitely have to be careful with it.

Scritto da: prashanth

Five Stars

good quality.

Scritto da: Cliente de Amazon

Broca sirve para lo que es, por la cantidad gastada.

la broca se siente pesada, la dureza del material del que esta hecho no puedes saberlo si no solo al utilizarlo con un material u otro. Yo lo utilice con lamina galvanizada de aprox 1.5 mm de grueso y utilice un taladro con muy bajas revoluciones y entre mas grande se vaya haciendo la perforacion aun mas, quiza unas 120 rev x min. (aprox ya que mi taladro es de velocidad variable mediante el gatillo) recomiendo utilizar aceite como lubricante mientras se perfora, si el aceite empieza a echar humo parar y dejar enfriar la broca y despues continuar. es cuestion de paciencia. no podria decir que otros metales ni que grosores puedes perforar, solo cuento mi experiencia con este que yo utilice. otra recomendación es no utilizarla como broca de inicio, utiliza otra broca normal para acero, puedes iniciar con 1/4 y ya despues ir agrandando de a poco con esta broca.

Scritto da: Warren E Benson

Evidently not for light-weight galvanzied steel

I needed to expand the 1/2" holes in a galvanized steel (1/16") to 7/8". This bit cut less than 5 holes before it wouldn't cut any further. Fortunately I had ordered three different Step Drill Bits for this exact reason. Two failed; but one excelled. Its more expensive, so I guess you get what you pay for... [see Klein Tools KTSB15 Step Drill Bit No15, Double Fluted, 3-hole sizes]

Scritto da: Sweet tooth

Absolutely useless

I'm actually re-writing this interview. This only deserves 1 star. First of all, was a complete different brand than what was advertised. Second of all, it is absolute junk. I used it to enlarge a hole in some mild steel. It didn't even cut, it didn't open up the hole by one step. Just spinning without biting in, basically like a dull bit. I would at least not have been so hard if it was just a cheap bit that only worked for a few holes, but the only thing this worked at was getting the metal hot. Junk

Scritto da: Luis

La herramienta indicada para mi tarea.

La usé para perforar una tabla de MDF/aglomerado y luego enroscar unas tuercas inserto de conicidad aproximada a la que tiene esta broca escalonada. En un inicio me indicaron que usara una broca común y corriente, si es que no quería comprar una herramienta especial para montar insertos, pero no me sentía a gusto con el barrenado parejo que habría obtenido de la broca común y tampoco quería gastar en una herramienta que usaría solo una vez, así que le dí una oportunidad a esta broca, resultando todo muy bien.