Dremel 9901 volframkarbiidist nikerdusotsik, 1/8” (3,2 mm) läbimõõt, nikerdamise ja graveerimise pöörlev tarvik, lõiketera (1 tk), hõbedane

Name: Dremel 9901 volframkarbiidist nikerdusotsik, 1/8” (3,2 mm) läbimõõt, nikerdamise ja graveerimise pöörlev tarvik, lõiketera (1 tk), hõbedane
Brand: Dremel
SKU: 0080596034733
Price: 28.90 EUR
Availability: InStock

Brand:Dremel

3.7/5

€
28.90

TOOTE KIRJELDUS Kasutage oma Dremeli pöörlevaid tööriistu maksimaalselt, kasutades meie uuenduslikku ja ulatuslikku pöörlevate tarvikute ja lisaseadmete sarja. Olenemata teie projektist on meil teile ideaalne lahendus. Dremeli tarvikud sobivad teie pöörleva tööriista sisse, et suurendada selle mitmekülgsust. Olenemata sellest, kas soovite nikerdada, graveerida, lõigata, lihvida või lihvida, on olemas Dremeli tarvik, et töö saaks täpselt tehtud. Seetõttu võimaldavad meie spetsiaalselt ehitatud Dremeli tarvikud teil oma projekti viimse detailini viia. Dremeli tarvikud on samuti värvikoodiga kasutuskategooriatesse, et oleks lihtsam oma projekti jaoks õiget tarvikut valida. 1/8 tolli. (3,2 mm) 9901 volframkarbiidist nikerdusotsikut saab kasutada agressiivsemate rakenduste jaoks kõvade materjalide, näiteks metallide, karastatud terase, tulekeraamika, malmi, plasti ja lehtpuu vormimiseks, silumiseks või lihvimiseks. Nikerdusotsik sobib hästi selliste projektide jaoks nagu metalli või klaasi graveerimine, kivi nikerdamine või valanditelt välklambi eemaldamine. Nikerdusotsaku silindriline kuju võimaldab materjali sügavalt eemaldada, lõikab tasaseid alasid, ümaraid servi ning teeb stopp- ja V-lõikeid. Tarviku ots teeb lameda põhjaga pilud ja sooned, lamedad küljelõiked ja V-kujulised lõiked, kui seda hoida 45-kraadise nurga all. Kaasas 1 pöörlev tarvik. Ühildub kõigi Dremeli juhtmega ja aku pöörlevate tööriistadega. Pole vaja otsida õiget kinnitust, kõigil Dremeli pöörlevatel tarvikutel on 1/8-tolline standardne vars. TOOTJALT Kiirlõikur, mis on valmistatud volframkarbiidist, teemantide kõrval kõige kõvemast materjalist, 1/8 (3,2mm) vars. Ideaalne eriti kõvade materjalide vormimiseks, silumiseks või eemaldamiseks, sealhulgas karastatud teras, roostevaba teras, malm, värvilised metallid, põletatud keraamika, plast ja kõva puit.

Summa

Lisa ostukorvi Osta kohe

EAN: 0080596034733

Kategooriad Tööriistad ja kodukaubad, Elektri- ja käsitööriistad, Elektritööriistad, Pöörlevad tööriistad,

Kasutamiseks koos pöörlevate tööriistadega, mille varre suurus on 1/8. Kaasas: 1/8 volframkarbiidist nikerdusotsik (x1). Nikerdusotsaku silindriline kuju võimaldab materjali sügavalt eemaldada, lõikab tasaseid alasid, ümaraid servi ning teeb stopp- ja V-lõikeid. Ideaalne selliste projektide jaoks nagu metalli või klaasi graveerimine, kivi nikerdamine või välklambi eemaldamine valanditelt. Dremeli väga vastupidavaid volframkarbiidist nikerdusotsikuid saab kasutada agressiivsemates rakendustes kõvade materjalide, näiteks metallide, karastatud terase, tulekeraamika, malmi, plasti ja kõva puidu vormimiseks, silumiseks või lihvimiseks. Imporditud. metallist.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Dremel
Color	‎Silver
Customer Reviews	4.7 4.7 out of 5 stars 743 ratings 4.7 out of 5 stars
Included Components	‎Unit^Instruction Guide
Is Discontinued By Manufacturer	‎No
Item model number	‎9901
Item Package Quantity	‎1
Item Weight	10 Grams
Item Weight	‎0.353 ounces
Manufacturer	‎Dremel
Material	Tungsten Carbide
Material	‎Tungsten Carbide
Measurement System	‎Metric
National Stock Number	‎3455-01-308-4389
Part Number	‎9901
Power Source	‎Corded-electric
Product Dimensions	‎1.6 x 0.8 x 0.2 inches
Size	Pack of 1
Size	‎Pack of 1
Warranty Description	‎No

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: AJ

Did exactly what I needed it to.

I used it to widen a hole on tempered steel. Works great.

Scritto da: chris.w.

Cleared right through a steel bolt and aluminum casing.

Allowed me to "drill" out a sheared-off M6 bolt and enlarger the hole for a threaded repair insert. Cleared through the steel bolt and aluminum casing with minimal effort. Will buy it again when this one dulls out.

Scritto da: Pat

Great tool

Cuts very well doesn't break if used properly. I trimmed 1/8 inch steel with it no problems.

Scritto da: Lady Chozens~

Worked!

Perfect for my use!

Scritto da: Robert Retford

Quality tool

Quality tool at a good price

Scritto da: Benny

Good sharp cutter for mild steel but very brittle

I bought this cutter to make a square hole in a metal stud - the type of metal studs used to hold up drywall in high-rise apartments/offices. The cutter worked great, it moved through the metal stud no problem. I did however have 2 problems that I'm writing this review so that others can benefit from my experience: 1.) The cutter is relatively short. I was trying to cut metal that was behind some drywall. So the cutter had to be long enough to get through the drywall and through the metal. Because of an obstruction on the wall surface, I had to hold the tool about 1.25" away from the metal. This made it so that only the very tip of the cutter would contact the metal. While it worked I can comment that the tool is very short, so consider you application before buying. 2.) The cutter is very brittle. I actually cracked the shaft of this tool and could not complete my job. Because of my particular use, the cutter was bouncing around a bit in the slot I was cutting. This caused the bit to break. After it broke, i used the remaining portion to try to cut again. It broke a second time. Final recommendations: This cutter is good for controlled cuts in mild metals where you can brace/secure the work and the tool. This tool is not very good for free-hand cutting as I was doing. Make sure that you control the tool well to prevent bouncing and cracking of the bit. I think I will re-try with a thicker-shanked bit. Perhaps 3/8" if I can find one.

Scritto da: Lonewolf

Tungsten carbide endmill

Not much to say, they are endmills in Tungsten carbide. Dremel pricing is too high for tooling like this. Came loose bouncing around in a big box, one of the two I ordered was stuck in bottom flap, ready to fall out. Luckily I received both, was close call.

Scritto da: Barry Wagner

Finished the task

I needed to shape an opening I drilled in the end of a hand railing. I was slightly off center and just needed to round over a bit to center the peg. This bit was perfect for the job and did it well and quick. It easily worked its way through oak. Job done.

Scritto da: WellTrainedMonkey

Cuts hardened metal effortlessly.

I was working on turning an old bastard file into a knife and needed some way to add minor details on the handle. This got the job done and it still holds its edge. One slight disappointment is that I found a tiny chip on one of the cutting edge, but thankfully it does not appear to affect the overall performance. Just not sure at what point that happened. Amazing performance considering the cost. Great bit to have with your dremel. I'm very happy with this bit.

Scritto da: Mike

Quality product

Needed to enlarge coil seat hole in the lower control arms of my resto. This did the trick like butter in less than a minute per hole with my Dremel. I had my doubts before purchasing, but proved unwarranted. Very pleased. Good durable product. As advertised.

Scritto da: Salvador elizalde santos

Empaque resellado, posible engaño

Regrese el artículo, porque se notaba que había sido abierto, y resellado, la etiqueta de dremel la blanca que ponen estaba despegada hacia un lado, y el plastico del empaque se veía irregular de un lado, como que fue resellado por eso la regrese, no me gusta el engaño si desde el inicio explicaran que esta nuevo pero resellado podría haber accedido pero esto me parecía un engaño y eso molesta.

Scritto da: AdrianS

Warning: Made in China

I bought a couple of these, together with some 9904 bits. While the 9904's are made in the US, the 9901 have the dreaded "Made in China" printed on them. After my experience with Chinese "titanium coated" drill bits, I expect that they are no better than the regular multipurpose bits, but at least twice as expensive (which seems to be confirmed by reviews on amazon.com). If you want Chinese cutting bits, you can get them much cheaper elsewhere, instead of paying a premium just for the Dremel logo.

Scritto da: Jody Wright

Performance on metal

I used this cutter with my Dremel to remove excess metal on new door strikes mounted on metal door frames installed with new handles. Now the doors close and lock with perfection.