DEWALTi lauasae alus, veerev alus, kokkupandav ja kaasaskantav, kerge ja kompaktne (DW7440RS)

Name: DEWALTi lauasae alus, veerev alus, kokkupandav ja kaasaskantav, kerge ja kompaktne (DW7440RS)
Brand: DEWALT
SKU: 0028877583075
Price: 490.84 EUR
Availability: InStock

Brand:DEWALT

3.8/5

€
490.84

TOOTE KIRJELDUS DEWALT DW7440RS lauasae rullimisalus. AMAZON.COM Mitmekülgne ja töökindel DEWALTi veerev lauasae alus ühendab vastupidava alumiiniumkonstruktsiooni uuenduslike detailidega. See hoiab teie tööd ideaalsel kõrgusel, aidates samal ajal hoida töödeldavaid detaile täpsete lõigete jaoks kontrolli all. Lisaks on see kõigest 33 naela koos kokkupandavate jalgade ja mugavate raskeveokite ratastega ehitatud hõlpsaks transportimiseks.Tugev, kerge alumiiniumkonstruktsioonKuigi see on ehitatud hõlpsaks kaasaskandmiseks, ei tee veereva sae alus jõudluses järeleandmisi. Tänu alumiiniumkonstruktsioonile on see lauasae alus nii tugev kui ka kerge. Vaid 33 naela kaaluvat alust on lihtne töökohale ja sealt tagasi transportida, mis võimaldab teil kasutada mitmekülgset ja stabiilset saeseadet – olenemata sellest, kuhu teie töö teid viib. See talub kuni 200 naelast koormust. Mugav disain, mis on stabiilne, kuid siiski kaasaskantav. Statiivi lai põhi ja tagumised nihutatud jalad on loodud pakkuma stabiilsust ja toetust sööda juhtimisele. Tööde vahel võimaldavad kiirvabastusega hoovad jalad kokku voltida, et neid oleks mugavam hoida, ning vastupidav tugijalg võimaldab seadmel püsti seista, kui saag on ikka kinnitatud, et parandada liikuvust ja mugavamat hoiustamist. Mugavuse suurendamiseks laadimisel ja mahalaadimisel kinnitatakse teie sae külge spetsiaalsed kiirühendusega statiivklambrid, mis muudavad sae aluse küljest lahtivõtmise uskumatult lihtsaks. Ergonoomilised detailid hoiavad teid mugavalt Kompaktne ja kerge ei ole kõik, mis muudab selle aluse transportimise lihtsaks. Selle suured raskeveokite rattad on ehitatud nii, et need veerevad üle astmete, äärekivide ja töökoha prahi. Lisaks libiseb sissetõmmatav pehme käepidemega käepide transpordi ajal välja, võimaldades teil saagi mugavalt selja taha tõmmata. See hoiab tööriista raskuse maapinna lähedal ning vähendab käte ja selja pinget. Sarnaselt nutikad detailid parandavad teie kasutuskogemust ka siis, kui laud on kasutusel. Kummist jalad ei lase statiivil siledatel pindadel libiseda ega kahjusta teie töödeldavaid detaile või põrandat, kus olete üles seatud. Lisaks asetab statiiv lõikelaua kõrgusele, mis on ideaalne mitmesuguste lauasaagidega töötamiseks, vähendades veelgi teie keha tarbetut pinget ja aidates teil kauem töötada. Seda DEWALTi veerevat lauasae statiivi toetab üks aastane piiratud garantii.Mis on BoxDW7440RS DEWALTi veerevas lauasae statiivis.

Summa

Lisa ostukorvi Osta kohe

EAN: 0028877583075

Kategooriad Tööriistad ja kodukaubad, Elektri- ja käsitööriistad, Elektritööriistad, Saed,

Lauasae veeremisalus. Lauasae veeremisalus. Lauasae veeremisalus. Lauasae veeremisalus. Lauasae veeremisalus.

Amperage	‎15 Amps
Batteries Included?	‎No
Batteries Required?	‎No
Blade Material	High Speed Steel
Blade Material	‎High Speed Steel
Brand	DEWALT
Brand	‎DEWALT
Certification	‎
Color	Multi
Color	‎Multi
Country of Origin	‎China
Current Rating	‎15 Amps
Customer Reviews	4.8 4.8 out of 5 stars 4,519 ratings 4.8 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Included Components	‎Table Saw Rolling Stand.
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item model number	‎DW7440RS
Item Package Quantity	‎1
Item Weight	‎42.6 pounds
Manufacturer	‎DEWALT
Material	‎Blend
Number of Teeth	‎30
Part Number	‎DW7440RS
Power Source	Corded Electric
Power Source	‎Corded Electric
Product Dimensions	‎20 x 9 x 34 inches
Product Dimensions	‎20"L x 9"W x 34"H
Size	‎One Size
Special Feature	‎Lightweight
Special Features	‎Lightweight
Speed	‎8500 RPM
Style	‎Table Saw Stand
Surface Recommendation	Aluminum
Surface Recommendation	‎Aluminum

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega^*

Teie hinnang

Scritto da: BS Smith

Compatibility with DWE7485

This review is for a DEWALT Table Saw Stand, Mobile/Rolling (DW7440RS) purchased 24 Nov 21 and the stand's compatibility with a DEWALT Table Saw for Jobsite, Compact, 8-1/4-Inch (DWE7485) purchased the same date. My Instruction Manual for the saw is N865128 (05/20); for the stand it's N044470 (AUG09). Note the stand manual predates the saw's by more than a decade. I've not written product reviews recently, but because I found no instance where correct advice is given for this stand and saw--including by DeWalt--I felt obliged to write this one. Many commenters have complained that stand instructions are unhelpful. The comments are correct. It's not that they're written in "English as a fourth language;" rather, by someone who either doesn't know how to make things clear, or doesn't care. For example, after usual Safety Guidelines, the first para of assembly instruction includes: "Ensure the long end of the axle is to the rear of the stand as shown." The axle is a tube with same-length threaded ends. How can it have a "long end"?! The small picture accompanying the text is no help, nor does it indicate which side of the stand is "the rear." Eventually, after seeing the assembled stand pictured on the shipping box, one realizes that DeWalt and safety decals likely are on the front of the stand, and that the opposite side therefore is the rear. (And in fact, once the stand was assembled and the saw mounted, I finally noticed that the safety decal also indicates "Front.") Knowing where the axle should go, it then becomes clear that the mounting points are not equidistant from axle ends, so that when installed, one end is "longer" than the other. So, instructions for assembly could be more helpful, but certainly the task is manageable. The real fun--and confusion!--begins when mounting the saw to the stand. First, in fairness to DeWalt, note that the stand, according to its Instruction Manual, is a "Universal Rolling Jobsite Table Saw Stand--Works with most jobsite table saws as designed. Some saws may require a plywood surface for attachment to stand." So, expectations shouldn't be high that detailed instructions will be provided for fitting any saw to the stand. On the other hand, Amazon currently is selling the stand and saw discussed here as a package, so one might hope specific instructions for combining the two would be provided. Hah! The stand manual indicates the stand has been UL-evaluated for use with DW744, DW744X and DW745 saws. DW744 and DW744X are 10" saws with a different base than the DWE7485. The DW745 also is a 10" saw, with a base more similar to the DWE7485, but still different. So, the manual provides no assurance that the stand is compatible with the DWE7485--no surprise, as it's probable this saw didn't exist when the manual was last updated. The manual does indicate "Measure the distance between the mounting holes of the table saw. Position the second mounting bracket onto the beam at this distance from the first mounting bracket." And the saw does have two sets of holes on both its lower tubes; the saw manual Fig. A indicates these as Part 9--Mounting Holes. So, one could expect these holes should be used for mounting the saw. But the first realization is that the hole diameter in the saw base is too small for the M8 screws provided with the stand for saw mounting. No problem, right? Just drill them out to 5/16". A second realization then is that the provided screws are too short to fasten the saw tube to the stand bracket, particularly at the wonky angle (30 degrees from vertical) of the holes. (An additional realization is that even if the existing Part 9 mounting holes and M8 screws could be used, the saw would be too close to the left end of the stand, because of the locator clip (J) "that keeps the saw from sliding left or right during operations and during transport.") At this point, the stand manual advises "If your saw holes do not line up with the mounting bracket slots, please follow the alternative mounting instructions below." These instructions then indicate a 3/4" plywood base and additional hardware are required. Grrr... Some reviewers have taken this route, some have made existing holes work with longer screws; some have drilled new holes. Others have removed the four plastic "feet" on the base of the saw and realized a threaded "nut" is affixed to the base tube. But the M8 mounting screws are too long (or have too little thread), such that the screw will not sufficiently tighten in this application. And at this point, some reviewers purchase shorter screws and fender washers, which works, or in one case, place provided mounting nuts within the tube (which seems difficult to make work). BUT none of this is necessary. The key is to note that Fig. A in the saw manual indicates Part 24--the plastic feet--are "Mounting holes (for mounting to DW7440RS brackets)." Ho ho! It's a shame this isn't discussed elsewhere in the manual, as it's easily missed. The feet however do indeed have holes in their bottom that go to the tube-mounted "nut." And when going through the feet to secure the saw to the stand, the provided M8 screws are the correct size; that is, they fit the threaded "nut" and tighten sufficiently. So, the simple solution is to use the provided M8 screw, flat washer and lock washer to go from underneath the stand's saw mounting bracket into the saw's feet hole. Picture attached. This will leave you with four nuts and four washers excess. And the DWE7485 securely mounted to the DW7440RS! Now, why doesn't the stand manual say that?!? Update 31 Dec 21 End-of-year reckoning: since writing the above review I've seen that the manual for saw DWE7485 in fact has more to say about mounting to stand DW7440RS than what's given in that manual's Fig. A. Page 6, Bench Mounting, indicates: "Holes (24) are also provided under the saw feet for mounting to DW7440RS brackets." Mea culpa!

Scritto da: Jaan Hjorth

Quality

Great stand. I originally bought the simple folding stand for simplicity It really needs the 4 bolts every time you use it. Bought this one, immediately missed the simplicity ^ small storage area of the foldup. I'm using the small Dewalt saw, & it shrinks to the size of a guitar amp & stands in the corner. This new table weighs about as much as the saw, & things got big & complicated fast. I sure like the wheels though. On the fence here, so I'm keeping both. Same table height BTW.

Scritto da: Stan J. Anderson Jr.

Sturdy product

I am lacking in space to store my tools so I bought this as it is eaiser to store and not have to bother taking it apart from stand. This works great. The instructions seem to make the assembly alot more difficult than it should be- Youtube showed how easy it was to assemble. The only problem is when attaching the saw that Ibought (both were sold almost as a package) the skrews to attach the saw to the saw to the stand barely fit through the holes and were in a difficult angle. Other than that. It is a good solid stand and it make easy to manuever and store my saw

Scritto da: Lara Karic Page

It works very well

This saw and stand work! Rip fence is accurate to a 16th out of the box. Cuts everything I have thrown at it so far without hesitation. The stand is very well built and rolls easily.

Scritto da: John Pecoraro

wish I purchased sooner!

terrific time saver regarding set up, well constructer and sturdy. Easy to assemble.

Scritto da: deborah

Fits Dewalt Flexvolt 8 1/4" table saw

This is a great, solid little stand and not at all rickety like the one actually recommended with the Dewalt Flexvolt 8 1/4" table saw. As others have commented, the instructions are completely useless. I got it put together after finding pictures online of how it's supposed to look assembled and the instructions for mounting the saw were just as criminally bad. A comment here had pictures of someone's saw on their stand and that's how I finally got it on properly.

Scritto da: Amazon Customer

Fits Dewalt table saw

I had to remove rubber pads on table saw to attach the saw to the stand. Bolts provided with stand too long. Had to replace with full thread shorter bolts. There should be better directions and example schematics to help with attachment.

Scritto da: Robert M St John Sr

Great tool

Simple to use and so much better on the back than carrying the saw. You won't regret buying this. Should have a long time ago.

Scritto da: Carl T.

Support Dewalt DW7440RS & scie de table Dewalt DWE7485 = Match parfait

L'assemblage du support et de la scie de table sur ce dernier, est facile bien que les instructions nous forcent à deviner. Aucun démontage ou retrait de pièce de la scie n'a été requis, le match est parfait sauf que les boulons d'assemblage de la scie sur ses 2 socles amovibles du support. soient un peu trop long, l'ajout de rondelles plates supplémentaires a été requises. La hauteur de la table de la scie , un fois assemblée sur son support, est à 35 po. du sol.Le retrait de la scie de sur son support via les poignées de démontage rapide s'effectue très bien. Passage de la position de travail à celle de déplacement se fait aisément.

Scritto da: Ben P.

This is very good fit for my DW744 table saw

This is very good fit for my DW744 table saw. I found out it was broken handle when I received it and opened the box. I went to local DeWalt service centre to order replacement parts for free because the damage may be caused by shipping or manufacturer to avoid to send it back to the seller-Amazon.ca. It work very good after the damage handle got replaced. The only little issue it is becoming a kind of heavy after I attached my table saw to the stand when I tried to pull the whole thing to upstairs from basement. Overall it is a very good table saw stand. It's convenience and easy for storage.

Scritto da: MD

Love it

Found the table saw stand on Amazon and it had the best price on the block - compared with Lowes, Home Depot, etc Was a bit iffy, but in the end I bit the bullet and got it. No regrets, great addition to my collection. Put my DeWalt table saw on it and I love it. A bit heavy compared with the cheaper version but 100% worth it. I recommend it

Scritto da: Jeff Sisson

Doesn’t fit all Dewalt Table Saws

For the most part easy to assemble but directions could have been clearer. Stand did not fit with my dewalt saw. I had to move the lock and this was made very difficult by the hex bolts that lacked depth for insert hex wrench and were extremely tight

Scritto da: Amazon Customer

Great addition by a reliable supplier.

This is a terrific addition to my home workshop. The movement and storage of my table saw just improved 100%! It was delivered in a timely fashion without hassle and is exactly what was seeking. Easy to assemble and as described in the write up. Fits perfectly my 10” Ridgid table saw. My only question is “why didn’t I buy this item sooner?!” ????