CURT 56189 sõidukipoolne kohandatud nelja kontaktiga haagise juhtmestik, sobib valitud Mitsubishi Outlanderile, must

Brand:CURT

3.4/5

94.15

Kui teie sõidukil pole haagise vedamiseks vajalikku juhtmestikku, on CURT kohandatud juhtmestik ideaalne lahendus. Kohandatud juhtmestik – mida nimetatakse ka T-pistikuks – on lihtne plug-and-play elektriseade, mis ühendatakse teie auto elektrisüsteemiga ja tagab standardse universaalse haagise juhtmestiku. Seda tehakse kahe või enama sõidukispetsiifilise OEM-iga ühilduva pistiku abil, mis ühendatakse tagatulede komplektiga, välistades vajaduse paigaldamise ajal lõikamiseks, liitmiseks ja jootmiseks. Kohandatud juhtmestikud on valmistatud sõidukipõhiselt ja kuigi need pole kõigi sõidukite jaoks saadaval, pakuvad need üht kiireimat, lihtsaimat ja turvalisemat viisi sõiduki pukseerimiseks. Sellel konkreetsel pistikühendusel on neljasuunaline lame pistikupesa ja see on loodud kohandatud juhtmestikuna, mis sobib Mitsubishi Outlanderi teatud aastate jaoks (sõiduki ühilduvuse kontrollimiseks vaadake rakenduse teavet). Kaasas on kõik vajalikud juhtmestiku komponendid, et luua usaldusväärne haagise juhtmestiku ühendus, samuti tolmukate, mis hoiab konnektori puhtana, kui seda ei kasutata. Teil on silme ees pilt oma järgmisest sihtkohast – võib-olla on see teie lemmikpüügikohas randuv paat, võib-olla on see kämping, kust avaneb vaade mõnele looduse meistriteosele, või võib-olla on see järgmine suur töökoht. Selle pildi reaalsuseks muutmine nõuab aga enamat kui lihtsalt unistamist. See nõuab tugevat ühendust ja õiget võimsust. CURTi kohandatud juhtmestik on valmistatud tööstuse kõige keerukama tehnoloogiaga ja on loodud hõlpsaks paigaldamiseks, pakkudes teile pikaajalist elektriühendust veokonksu seadistamiseks.

TOLMUKATE. Pikaajalise kasutuse ja ilmastikukindluse tagamiseks on sellel 4-pooluselisel haagise valgustuse juhtmestikul kummist tolmukate. Kui seda ei kasutata, sobib see hõlpsasti 4-suunalise lamepistiku külge, kaitstes seda välistingimuste eest. USALDUSVÕIME. See 4-suunaline haagise juhtmestik on ehitatud pindpaigaldustehnoloogiaga. Seda tüüpi vooluringid toodavad vähem soojust, optimaalset valgustugevust ja vastupidavat jõudlust. SÕIDUKI SPETSIIFILINE. See järelturu haagise juhtmestik on mõeldud Mitsubishi Outlanderi valitud aastate jaoks. STANDARDÜHENDUS. Seda pistikühendusega nelja tasapinnalise haagise juhtmestikku saab kasutada haagise tagatulede, piduritulede ja suunatulede ühendamiseks. 4-suunaline haagise tulede juhtmestik on populaarne paljudel haagistel, lisades teie sõidukile mitmekülgseid pukseerimisvõimalusi. LIHTNE PAIGALDADA. Ei mingit lõikamist! Ei mingit splaissimist! See haagise juhtmestiku komplekt ühendatakse teie sõiduki olemasoleva tehasejuhtmestikuga ja varustab selle standardse 4-kontaktilise haagise juhtmestiku pistikuga haagise ühendamiseks ja pukseerimiseks.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.3 4.3 out of 5 stars 118 ratings 4.3 out of 5 stars
Exterior ‎Painted
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 6 x 3 inches
Item model number ‎56189
Item Weight ‎1.4 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎56189
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎56189
Product Dimensions ‎9 x 6 x 3 inches

3.4

13 Review
5 Star
69
4 Star
13
3 Star
7
2 Star
3
1 Star
7

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega*

Scritto da: ABC
Working just fine.
For whatever reason, the original wiring harness for my trailer lights failed. I ordered this one to fit my car and I now have trailer lights again. Since I didn't have a place to work on the car, I had our local U-Haul install the wiring harness.
Scritto da: DOBY DADDY
not plug and play
I thought this is supposed to be plug and play. The power wire is not plug and play and needs to be ran under the carpet along the edge so door sill panels and center column lower trim panel need to be taken off. I didn't go through the firewall. I just plugged it into the fuse box under the dash. Also had to drill a hole in the rear floor pan above the spare tire so the spare tire had to be dropped. Whole thing took about an hour.
Scritto da: Rev DoPray
2018 Mitsubishi Outlander Phev Successful Install
I was able to install this into my 2018 Mitsubishi Outlander PHEV GT S-AWC. Everything was hooked up in the back without needing to run the wire under the car to the battery. I just hooked it up to the battery in the back. There also wasn’t a need for any trim/panel removal tools. The instructions were useless but I simply looked at the wiring diagram and installed it. Although I haven’t tested it with my trailer I am giving this product 5-Stars. If I run into difficulty with it functioning correctly I will update my review.
Scritto da: Asher04
Not for Vehicle that already has Factory Tow Package
Before you buy this product - check to see if your vehicle has the factory tow package included. To find out if you do, check the installation video from etrailer (for their product) and the installer will point out in the hood what you need to look for. If you do have the factory tow package go with the model #56296 (ignore the vehicle fit from Amazon: it will say it will not fit your vehicle). Only go with this product if you don't have the factory tow package. I didn't realize I had the factory tow package until I went through the installation steps.
Scritto da: Jana M. Kleffman
Worked Great
Did what it said it was gonna do. Took about 30 minutes to install, nothing complex. Make sure you have the ability to lift your vehicle because you are going to need to crawl along the ground a bit to get the wire up to the front of the vehicle. Not a big issue with ramps. Overall, good kit.
Scritto da: Jason Brinckmann
Watch my video for Installation!!!!
The media could not be loaded. Everything you need and not too terrible to install yourself! Watch my detailed video for a complete overview on the installation because the instructions page that it comes with (-1 star) has incomplete written directions and the photos only show the panel removing in the trunk.
Scritto da: Moises Pimentel
To connect it’s on the driver side left side thank you
It fits perfectly on the video it shows on the right side of the rear end of the 2018 outlander but on the outlander it will be on the left rear of the light fixture the only thing that was different but it works perfectly fine thank you
Scritto da: TLB
Works great
Works great on my three row 2019 Mitsubishi Outlander. Easy to setup even though I had to crawl under my car to run the wire to the engine bay. Electrical tape helps keep the connectors attached to the wires.
Scritto da: Martin Thomas
Good quality and very nice custom fit
Easily plugs into lighting system for a professional installation.
Scritto da: John
No wires to splice
2015 outlander . Easy plug-ins. No cut wires , so if electrical problems come up later you can unplug harness and start trouble shoot the vehicle only . - Routing wire too frount of vehicle can be done with no drilling but a little of a challenge if you are not a young man ????
Scritto da: Amazon Customer
Easy install and working fine
I purchased and installed myself following instructions from YouTube. It's working great.
Scritto da: Gary wilkinson
Excellent and on time
Scritto da: Jim B.
Good for a 2019 Mitsubishi outlander phev
Used this on a 2019 Mitsubishi outlander phev worked great.

Seotud tooted

hot
Ostjad Tooted B2426FS Vormitud hingerihm
3.8/5

€ 33.54

Ostjad Tooted B2426FS Vormitud hingerihm
3.8/5

€ 33.54

hot
RV Designer P720 pistikupesa
0.1/5

€ 28.65

RV Designer P720 pistikupesa
0.1/5

€ 28.65

Avastage meie rahvusvaheline võrgustik

Saadame 28 riiki, üle 200 000 toote. Olge kursis, tellige uudiskiri.

Array