AmpFlow M27-150 harjatud elektrimootor, 150 W, 12 V, 24 V või 36 V alalisvoolu, 3800 p/min

Brand:AmpFlow

2.8/5

87.45

Mootor AmpFlow M27-150 on loodud pakkuma head jõudlust ja tõhusust ökonoomse hinnaga. See saavutatakse nelja harja ning täiustatud elektromagnetilise arvutimodelleerimise ja -disaini kasutamisega. Mootori läbimõõt on 2,7 tolli ja pikkus 3,9 tolli. Võll sõidab kahes kvaliteetses kuullaagris. Raskete mootorite juhtmed on 12 tolli pikad. Mootor kaalub 3,0 naela ja see on viimistletud musta pulbervärviga. Seda pööratavat mootorit saab kasutada pingetel vahemikus 12V kuni 36VDC. 24 V pingel on tühikäigukiirus 3800 p/min. Nimiväljundvõimsus on 150 W ja 2800 p/min ja 9 amprit. Maksimaalne kasutegur on 79%.See mootor on varustatud 11-hambalise ketirattaga #25 rullketi jaoks.AmpFlow® mootoreid kasutatakse mitmesugustes rakendustes, sealhulgas robotites, elektrilistes tõukeratastes, elektriratastes ja muudes isiklikes transpordisüsteemides. Otsige Amazonist AmpFlow mootorite jaoks rohkem valikuid.

Tarnitakse 11-hambalise ketirattaga #25 keti jaoks. Maksimaalne kasutegur 24 V juures: 79%. Pidev võimsus: 150 vatti (1/5 hobujõudu). Koormuseta pöörete arv: 3800 24 volti juures; Saab kasutada pingega 12V kuni 36VDC. Selle läbimõõt on 2,7 tolli (68 mm) ja pikkus 3,9 tolli (99 mm).
Brand AmpFlow
Country of Origin USA
Horsepower 150 Watts
Item model number M27-150
Item Weight 3 Pounds
Manufacturer AmpFlow
Package Dimensions 6.6 x 4.4 x 4.4 inches; 3 Pounds
Speed 3800 RPM
Voltage 24 Volts, 12 Volts

2.8

5 Review
5 Star
48
4 Star
11
3 Star
11
2 Star
30
1 Star
0

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega*

Scritto da: Lorenzo Gonzalez
Good motor if you know what you need.
I work this thing pretty hard, driven by a Dimension Engineering "Sabertooth" motor controller. It whips a moving target system back and forth across 60 feet of cable very nicely and rapidly indeed, especially at 24V. I fashioned a very simple mount by drilling and milling a 4"-long piece of 1-1/2" x 1/8" L-angle aluminum (available at any good hardware store in 36" lengths and easy to cut with hacksaw, cordless drill, dremel, if you don't have a mill). Only two of the faceplate screws (#8 machine screws, if I recall correctly) go into the mount, but it's plenty.
Scritto da: chinatwanger
This could all be easily eliminated if they just turned a step in the ...
A cheap motor for cheap. So OK.Be careful taking off the sprocket... The threads on the motor shaft are LEFT-Handed (as they should be). So if you over tighten the shaft nut it will force the shaft bearing (inside the motor) down onto the armature coil. Then to get the motor to work again you'll have to try and pull that bearing off the coils and back into position. This could all be easily eliminated if they just turned a step in the shaft instead of using a collar under the sprocket. That would keep this from happening. But the motor works and was cheap so I can live with it.
Scritto da: Linhking
It's working well, but not very good.
I use it for my project handle a windmill turbine, it got hot to much after 30', I don't know how long it's alive if hot to much. with #25 chain not fit for normal teeth pulley, so take a lot of personal technical to make it working the way I need.
Scritto da: Zaen Q.
exactly what i expected
amazing generator, fairly free moving. Will definitely look to purchase the 300W dc motor soon.
Scritto da: jose
Five Stars
Ver y good

Seotud tooted

Avastage meie rahvusvaheline võrgustik

Saadame 28 riiki, üle 200 000 toote. Olge kursis, tellige uudiskiri.

Array