3M paljaste metallide õmbluste tihendaja, 08310, beež, kaheosaline, mitte longus, iseseguv epoksiid, 200 ml/6,75 fl untsi kasseti epoksübeež

Brand:3M

3.8/5

88.31

3M™ Bare Metal Seam Sealer 08310 on tugev ja painduv tihendusmaterjal, mis on loodud paljasmetallide, näiteks terase või alumiiniumi, samuti krunditud või värvitud metallide tihendamiseks kokkupõrke parandamisel. Kaheosalist isesegunevat epoksütihendit saab hõlpsasti pahteldada, töödelda tööriistadega või pintseldada õmblustesse ning see kõveneb kõigest 15 minutiga. Sellel on neutraalne beež värv. Kasutage koos 3M™ Performance Manual aplikaatoriga 08117, 3M™ Manual Cartridge Aplikaatoriga 08571 või 3M™ Performance Pneumaatilise aplikaatoriga 09930 (müüakse eraldi). Kõvenemisaeg: 1 tund Käsitsemisaeg: 1-10 minutit Tööaeg: 10 minutit Värvimisaeg: 15 minutit

Ainult tööstuslikuks/tööotstarbeliseks kasutamiseks. Mitte tarbijale müügiks ega kasutamiseks. NEUTRAALBEEEŽ: värv võib vähendada värvimismaterjali ja aega. KIIRE SEADISTAMINE: kõveneb kõigest 15 minutiga, mis tagab tõhusa poeaja. RASKE KEHA VALEM: Mittevajumine tagab puhta ja tõhusa tööriistade töötlemise vertikaalsetes ja horisontaalsetes õmblustes. SPETSIAALSELT LOODUD: ei kahane, pragune ega eraldu gaasist. KAHEOSALINE EPOKSÜÜK: Tihendusvahend moodustab paljaste metallvuukide jaoks tugeva ja painduva tihendi.
Brand 3M
Color Beige
Country of Origin USA
Department unisex-adult
Is Discontinued By Manufacturer No
Item model number 08310
Item Weight 6.75 Ounces
Manufacturer 3M
Material Epoxy
Product Dimensions 12 x 9.63 x 5.38 inches; 6.75 Ounces
Style Epoxy

3.8

8 Review
5 Star
86
4 Star
7
3 Star
3
2 Star
1
1 Star
3

Kirjutage oma arvustus

Teie e-posti ei avaldata. Kõik kohustuslikud väljad on tähistatud tähisega*

Scritto da: john g.
as described
good price fast delivery
Scritto da: XDAEDAEX
Does the job
Worked its purpose
Scritto da: snatch
Great product if used correctly
I used this for sealing drip rails on a Ranger... very pleased with the results. It does self level quickly and evenly and looks great. I used about 1/2 of the 200ml tube for both sides and probably put in quite a bit more than the factory did...but one tube would easily do both drip rails on a full size truck I think. Since it is self levelling you must dam up the ends with masking tape and make sure the surface itself is level... and plan to grind out some of it on the ends, easily done with a small file. Overnight cure is better, the data sheet says paintable within a short period but it was still a bit tacky after an hour... rock hard the next day and very easy to finish the ends.
Scritto da: Jan
Very "epoxy" like. It's an epoxy after-all
Not sure about self-leveling, was expecting something more "fluidy", the viscosity and stickiness is just like honey and as a matter of fact - as epoxy :). It's likely great glue for gluing separate pieces, but not great for filling voids, due to low viscosity and high stickiness. The nozzle with the cartridge is bulky and exponentially grows with the gun, so not great for tight spaces. The proprietary gun is another story for itself... Should have gone with a smaller package with a thumb applicator instead...
Scritto da: chad caro
Great product
Worked as it should
Scritto da: Max Power
Bought to replace seam sealer on the drip rails of ...
Bought to replace seam sealer on the drip rails of a 71 Chevy pickup. Make sure you level the vehicle - mask off areas you don't want this stuff on and PEEL off the tape ASAP before it sets up or it is there forever (and trying to peel it from under sealer will result in sealer getting pulled up as well). You cannot use this on vertical sections as it flows for at least five minutes before it begins to set up. Ended up buying the heavy bodied seam sealer (3M 8303) to do the vertical sections first (along with a few spots on the firewall & cowl) then used the 08307 for the level areas (came out glass smooth). Wear gloves - it is messy if you are not careful.
Scritto da: Max Power
Bought to replace seam sealer on the drip rails of ...
Bought to replace seam sealer on the drip rails of a 71 Chevy pickup. Make sure you level the vehicle - mask off areas you don't want this stuff on and PEEL off the tape ASAP before it sets up or it is there forever (and trying to peel it from under sealer will result in sealer getting pulled up as well). You cannot use this on vertical sections as it flows for at least five minutes before it begins to set up. Ended up buying the heavy bodied seam sealer (3M 8303) to do the vertical sections first (along with a few spots on the firewall & cowl) then used the 08307 for the level areas (came out glass smooth). Wear gloves - it is messy if you are not careful.
Scritto da: Inland Classic Auto LLC
Spot on
Sticks well to bare metal. Quick drying

Seotud tooted

Avastage meie rahvusvaheline võrgustik

Saadame 28 riiki, üle 200 000 toote. Olge kursis, tellige uudiskiri.

Array